This page covers 4T5502, a bucket pin for 35 Ton Wheel Loader buckets. Body material is 42CrMo Alloy Steel at HRC 50-54, pin size 45 x 255mm, net weight 1.70 kg. Typical duty is coal yard and bulk material handling, where abrasive fines and shock loading attack the pin groove first.
Coal yard machines articulate the bucket constantly, so the pin sees millions of small rotations rather than occasional shock. Wear at the body is therefore the dominant mode, and 4T5502 uses 42CrMo at HRC 50-54 to hold diameter over long intervals. The 45 mm section suits 35 ton class loader linkage without modifying the bucket ears.
In coal yard and bulk material handling the pin does not simply rotate in a clean bore. Grit enters the joint, the retainer groove takes repeated side load, and the pin body sees a mix of abrasion and impact. 4T5502 is dimensioned for that duty: 45 mm body, 255 mm overall length, 1.70 kg net weight, 42CrMo Alloy Steel through the section with HRC 50-54 after heat treatment.
Each heat is checked by spectrometer before casting. Pins are then hardened and tempered to HRC 50-54, and the groove is machined after heat treatment so the retainer seats without play. Head, body and groove are hardness tested on a sampling basis, and the lot report can travel with the shipment.
Standard finish is black oxide. It slows corrosion in the bore and keeps the pin free during the next tooth change. For wet, coastal or high humidity sites ask for zinc plating instead.
Drive the pin in with a soft faced hammer, never a steel drift directly on the head. Seat the retainer fully, then check for movement by hand. Replace pin and retainer together, because a worn retainer will hammer a new pin loose within days.
Repeatable fit. 4T5502 is machined to the same drawing on every batch, so a second order drops into the same bore without reaming or shimming.
Hardness matched to duty. HRC 50-54 in 42CrMo Alloy Steel for coal yard and bulk material handling. Too hard and the pin cracks at the groove, too soft and it wears oval within weeks. This grade is the balance point for 35 Ton Wheel Loader buckets.
Groove geometry. The retainer seat is machined after heat treatment, not before, which keeps groove width stable and stops the retainer working loose.
Traceable lots. Part number laser marked, lot identified on the carton, inspection report on request. Useful when you supply fleets under contract.
Pin size 45 x 255mm, weight 1.70 kg, finish black oxide, primary number 4T5502, machine class 35 Ton Wheel Loader, application coal yard and bulk material handling.
Most of our distributor customers combine this number with teeth, adapters and retainers in a single container. Send the full list and we will confirm weights, carton counts and a single FOB price for the mixed load.
| Part Number | 4T5502 pin |
| Product Type | Bucket Pin |
| Material | 42CrMo Alloy Steel |
| Hardness | HRC 50-54 |
| Pin Diameter | 45 mm |
| Pin Length | 255 mm |
| Net Weight | 1.70 kg |
| Machine Class | 35 Ton Wheel Loader |
| Surface Finish | Black Oxide |
| Application | coal yard and bulk material handling |
| Warranty | 6 months against casting and heat treatment defects |
| Minimum Order | 10 pieces |
| Packing | Neutral carton, no third party brand or logo printed |
| Compatible Reference No. | Notes |
| 4T5502 | Primary number |
| 4T5501 | Interchange reference, verify against sample before ordering |
| 966 series | Interchange reference, verify against sample before ordering |
| 8E0466 pin | Interchange reference, verify against sample before ordering |
Each pin leaves the line oiled, wrapped and labelled, consolidated into export corrugated cartons on a fumigation free pallet. Packing is deliberately neutral, with no third party brand name, logo or printed artwork, which keeps the goods clean for resale. FOB Ningbo or Guangzhou as standard, CIF and DDP on request.
How do I confirm the pin fits my machine?
Send the machine model, bucket part number or a photo of the old pin with its length and diameter. We will cross check the 4T5502 against our fitment data before you order.
Is the pin supplied with the retainer?
Yes, 4T5502 is supplied as a bucket pin kit. If you only need the pin or only the retainer, state this in the inquiry and we will quote separately.
What is the packing like?
Neutral carton with no third party logo. Each pin is wrapped and part number labelled, and the carton is export grade corrugated suitable for sea freight.
Send your machine model, the number you are replacing and the quantity per size. You will receive a quotation with FOB price, carton count, total weight and lead time within 24 hours on working days. Sample pins for stock sizes can be arranged before the bulk order.