1U3352 is our production pin and retainer for 25 Ton Excavator machines. Machined from 42CrMo Alloy Steel, heat treated to HRC 50-54, finished black oxide. It is selected by contractors working in general earthworks and pipe trenching who need a pin that holds its diameter through the full service interval.
General earthworks on 25 ton class machines is the most common duty we quote for, and 1U3352 is the volume line. 40 mm body in 42CrMo at HRC 50-54, supplied with a matched retainer and laser marked for fleet traceability. Distributors typically stock this alongside 7T3402 so both J350 and 325 class machines are covered from one shelf.
In general earthworks and pipe trenching the pin does not simply rotate in a clean bore. Grit enters the joint, the retainer groove takes repeated side load, and the pin body sees a mix of abrasion and impact. 1U3352 is dimensioned for that duty: 40 mm body, 240 mm overall length, 1.40 kg net weight, 42CrMo Alloy Steel through the section with HRC 50-54 after heat treatment.
Each heat is checked by spectrometer before casting. Pins are then hardened and tempered to HRC 50-54, and the groove is machined after heat treatment so the retainer seats without play. Head, body and groove are hardness tested on a sampling basis, and the lot report can travel with the shipment.
Standard finish is black oxide. It slows corrosion in the bore and keeps the pin free during the next tooth change. For wet, coastal or high humidity sites ask for zinc plating instead.
Drive the pin in with a soft faced hammer, never a steel drift directly on the head. Seat the retainer fully, then check for movement by hand. Replace pin and retainer together, because a worn retainer will hammer a new pin loose within days.
Contractors running 25 Ton Excavator machines in general earthworks and pipe trenching tell us the two failure patterns that matter are oval wear in the body and loosening of the retainer. 1U3352 addresses both: the body diameter is held tight to the tooth bore, and the retainer groove is cut after heat treatment so its width does not change when the pin is hardened.
The numbers listed below are the references we ship against most often for this size. They are supplied as compatibility information only, so the buyer can confirm the match against the machine serial or the old part.
Regular sizes are held in stock for shipment within 3-7 working days. Non stock sizes and OEM production run 20-25 days from drawing confirmation. Minimum order 10 pieces per size, mixed sizes allowed.
| Part Number | 1U3352 |
| Product Type | Pin and Retainer |
| Material | 42CrMo Alloy Steel |
| Hardness | HRC 50-54 |
| Pin Diameter | 40 mm |
| Pin Length | 240 mm |
| Net Weight | 1.40 kg |
| Machine Class | 25 Ton Excavator |
| Surface Finish | Black Oxide |
| Application | general earthworks and pipe trenching |
| Warranty | 6 months against casting and heat treatment defects |
| Minimum Order | 10 pieces |
| Packing | Neutral carton, no third party brand or logo printed |
| Compatible Reference No. | Notes |
| 1U3352 | Primary number |
| 1U3351 | Interchange reference, verify against sample before ordering |
| 325 series | Interchange reference, verify against sample before ordering |
| 7T3402 compatible | Interchange reference, verify against sample before ordering |
Oiled and wrapped pins, part number and lot on the label, export corrugated carton, fumigation free pallet. No third party brand, logo or artwork appears on the product or the packaging. Shipments load from Ningbo or Guangzhou, and we quote CIF or DDP where the buyer prefers a landed price.
Does the price include the retainer?
The quoted price covers the pin and retainer kit as described. Volume pricing from 200 pieces and mixed container loading are available.
What happens if a pin fails early?
Report the lot number and photos. Confirmed casting or heat treatment defects are replaced free within the 6 month warranty period.
Can you supply other numbers in the same shipment?
Yes. Most buyers load 5 to 15 part numbers per container. Send your list and we will consolidate the order and confirm total weight and volume.
Send your machine model, the number you are replacing and the quantity per size. You will receive a quotation with FOB price, carton count, total weight and lead time within 24 hours on working days. Sample pins for stock sizes can be arranged before the bulk order.