4652262 is our production bucket pin for 20 Ton Excavator machines. Machined from 45# Carbon Steel, heat treated to HRC 45-50, finished black oxide. It is selected by contractors working in foundation piling and basement excavation who need a pin that holds its diameter through the full service interval.
Foundation work on 20 ton class machines is steady, high cycle duty at moderate abrasion. 4652262 uses a 30 mm 45# carbon steel body at HRC 45-50, which matches that duty without paying for alloy grade that the application does not need. Straightness is checked on every batch because a bent pin in a basement dig will stop the machine until it is cut out.
Repeatable fit. 4652262 is machined to the same drawing on every batch, so a second order drops into the same bore without reaming or shimming.
Hardness matched to duty. HRC 45-50 in 45# Carbon Steel for foundation piling and basement excavation. Too hard and the pin cracks at the groove, too soft and it wears oval within weeks. This grade is the balance point for 20 Ton Excavator buckets.
Groove geometry. The retainer seat is machined after heat treatment, not before, which keeps groove width stable and stops the retainer working loose.
Traceable lots. Part number laser marked, lot identified on the carton, inspection report on request. Useful when you supply fleets under contract.
Pin size 30 x 180mm, weight 0.60 kg, finish black oxide, primary number 4652262, machine class 20 Ton Excavator, application foundation piling and basement excavation.
Most of our distributor customers combine this number with teeth, adapters and retainers in a single container. Send the full list and we will confirm weights, carton counts and a single FOB price for the mixed load.
In foundation piling and basement excavation the pin does not simply rotate in a clean bore. Grit enters the joint, the retainer groove takes repeated side load, and the pin body sees a mix of abrasion and impact. 4652262 is dimensioned for that duty: 30 mm body, 180 mm overall length, 0.60 kg net weight, 45# Carbon Steel through the section with HRC 45-50 after heat treatment.
Each heat is checked by spectrometer before casting. Pins are then hardened and tempered to HRC 45-50, and the groove is machined after heat treatment so the retainer seats without play. Head, body and groove are hardness tested on a sampling basis, and the lot report can travel with the shipment.
Standard finish is black oxide. It slows corrosion in the bore and keeps the pin free during the next tooth change. For wet, coastal or high humidity sites ask for zinc plating instead.
Drive the pin in with a soft faced hammer, never a steel drift directly on the head. Seat the retainer fully, then check for movement by hand. Replace pin and retainer together, because a worn retainer will hammer a new pin loose within days.
| P/N | 4652262 |
| Item Type | Bucket Pin |
| Steel Grade | 45# Carbon Steel |
| Hardness | HRC 45-50 |
| Diameter | 30 mm |
| Overall Length | 180 mm |
| Weight | 0.60 kg |
| Class Fitment | 20 Ton Excavator |
| Coating | Black Oxide |
| Duty | foundation piling and basement excavation |
| Warranty | 6 months against casting and heat treatment defects |
| Minimum Order Quantity | 10 pieces |
| Packing Method | Neutral carton, no third party brand or logo printed |
| Compatible Reference No. | Notes |
| 4652262 | Primary number |
| 4652263 | Interchange reference, verify against sample before ordering |
| ZX200 series | Interchange reference, verify against sample before ordering |
| 4196846 | Interchange reference, verify against sample before ordering |
Each pin leaves the line oiled, wrapped and labelled, consolidated into export corrugated cartons on a fumigation free pallet. Packing is deliberately neutral, with no third party brand name, logo or printed artwork, which keeps the goods clean for resale. FOB Ningbo or Guangzhou as standard, CIF and DDP on request.
Can you produce from our drawing?
Yes. Send a drawing or sample and we will confirm material, tolerance and heat treatment, then quote for OEM production with your part number marked.
What is the lead time for 500 pieces?
Stock sizes ship in 3-7 days. Made to order quantities of 500 pieces run about 20-25 days after drawing confirmation and deposit.
How do you control hardness?
Every heat is checked by spectrometer, then pins are sampled for Rockwell hardness at the head, body and groove. 4652262 is held within HRC 45-50.
Send your machine model, the number you are replacing and the quantity per size. You will receive a quotation with FOB price, carton count, total weight and lead time within 24 hours on working days. Sample pins for stock sizes can be arranged before the bulk order.