This page covers 220-9089, a retainer pin for 30 Ton Excavator buckets. Body material is 40Cr Alloy Steel at HRC 48-52, pin size 20 x 90mm, net weight 0.18 kg. Typical duty is demolition debris and concrete recycling, where abrasive fines and shock loading attack the pin groove first.
Demolition work reverses the normal load pattern: the bucket is often levered sideways against concrete, so the retainer sees lateral force rather than simple rotation. 220-9089 is a 20 mm retainer pin intended for that duty, zinc plated to survive the dust and moisture typical of recycling yards. Check the retainer every 100 hours on this kind of work; it is the part that fails first.
Contractors running 30 Ton Excavator machines in demolition debris and concrete recycling tell us the two failure patterns that matter are oval wear in the body and loosening of the retainer. 220-9089 addresses both: the body diameter is held tight to the tooth bore, and the retainer groove is cut after heat treatment so its width does not change when the pin is hardened.
The numbers listed below are the references we ship against most often for this size. They are supplied as compatibility information only, so the buyer can confirm the match against the machine serial or the old part.
Regular sizes are held in stock for shipment within 3-7 working days. Non stock sizes and OEM production run 20-25 days from drawing confirmation. Minimum order 10 pieces per size, mixed sizes allowed.
In demolition debris and concrete recycling the pin does not simply rotate in a clean bore. Grit enters the joint, the retainer groove takes repeated side load, and the pin body sees a mix of abrasion and impact. 220-9089 is dimensioned for that duty: 20 mm body, 90 mm overall length, 0.18 kg net weight, 40Cr Alloy Steel through the section with HRC 48-52 after heat treatment.
Each heat is checked by spectrometer before casting. Pins are then hardened and tempered to HRC 48-52, and the groove is machined after heat treatment so the retainer seats without play. Head, body and groove are hardness tested on a sampling basis, and the lot report can travel with the shipment.
Standard finish is zinc plated. It slows corrosion in the bore and keeps the pin free during the next tooth change. For wet, coastal or high humidity sites ask for zinc plating instead.
Drive the pin in with a soft faced hammer, never a steel drift directly on the head. Seat the retainer fully, then check for movement by hand. Replace pin and retainer together, because a worn retainer will hammer a new pin loose within days.
| P/N | 220-9089 |
| Item Type | Retainer Pin |
| Steel Grade | 40Cr Alloy Steel |
| Hardness | HRC 48-52 |
| Diameter | 20 mm |
| Overall Length | 90 mm |
| Weight | 0.18 kg |
| Class Fitment | 30 Ton Excavator |
| Coating | Zinc Plated |
| Duty | demolition debris and concrete recycling |
| Warranty | 6 months against casting and heat treatment defects |
| Minimum Order Quantity | 10 pieces |
| Packing Method | Neutral carton, no third party brand or logo printed |
| Compatible Reference No. | Notes |
| 220-9089 | Primary number |
| 220-9090 | Interchange reference, verify against sample before ordering |
| 7T3402 retainer | Interchange reference, verify against sample before ordering |
| J400 series | Interchange reference, verify against sample before ordering |
Standard export packing: oiled pin, inner wrap, part number label, corrugated carton, pallet. Neutral presentation throughout, no third party brand or logo anywhere in the shipment. Port of loading is Ningbo or Guangzhou; we can also quote CIF and DDP so the landed cost is clear before you commit.
Can you send a sample before the bulk order?
Yes. Sample pins for stock sizes can be sent by express, freight collect, so you can verify fit and hardness before committing to volume.
What is the smallest order you accept?
10 pieces per size. Below that the per unit freight cost usually does not justify the shipment.
Do you offer a fitment drawing?
Yes, on request we provide a dimensional sketch of 220-9089 with diameter, length and groove position for your engineering check.
Send your machine model, the number you are replacing and the quantity per size. You will receive a quotation with FOB price, carton count, total weight and lead time within 24 hours on working days. Sample pins for stock sizes can be arranged before the bulk order.