The 1U3252 is a pin and retainer for 12 Ton Excavator buckets, produced in our own foundry and machining line from 42CrMo Alloy Steel and hardened to HRC 50-54. It is built for trenching and utility digging in compacted clay, where a pin that wears oval or cracks at the groove stops the machine and costs a shift.
On 12 ton class machines the pin is changed more often than on larger units, typically every 600 to 900 working hours in clay and mixed fill. That frequency makes handling speed and fit consistency the deciding factors. 1U3252 is kept as a stock line so a workshop can re-pin a bucket the same day rather than waiting on an imported order. The 25 mm body is held within the tooth bore tolerance, which means the operator does not fight a tight pin in the field.
In trenching and utility digging in compacted clay the pin does not simply rotate in a clean bore. Grit enters the joint, the retainer groove takes repeated side load, and the pin body sees a mix of abrasion and impact. 1U3252 is dimensioned for that duty: 25 mm body, 140 mm overall length, 0.42 kg net weight, 42CrMo Alloy Steel through the section with HRC 50-54 after heat treatment.
Each heat is checked by spectrometer before casting. Pins are then hardened and tempered to HRC 50-54, and the groove is machined after heat treatment so the retainer seats without play. Head, body and groove are hardness tested on a sampling basis, and the lot report can travel with the shipment.
Standard finish is black oxide. It slows corrosion in the bore and keeps the pin free during the next tooth change. For wet, coastal or high humidity sites ask for zinc plating instead.
Drive the pin in with a soft faced hammer, never a steel drift directly on the head. Seat the retainer fully, then check for movement by hand. Replace pin and retainer together, because a worn retainer will hammer a new pin loose within days.
1U3252 is dimensioned as a pin and retainer for 12 Ton Excavator buckets working in trenching and utility digging in compacted clay. The table below lists the primary number and the interchange references we ship against most often. Where a machine has been re-pinned or the bucket rebuilt, always check the bore diameter and groove position on the old part before ordering.
Two dimensions decide whether a pin lasts a month or a season: body diameter against the tooth bore, and groove width against the retainer. We hold both on our own machining line rather than buying finished pins on the open market, so a repeat order keeps the same fit as the first shipment.
Replace when the body shows a step of more than 1 mm, when the groove has widened enough for the retainer to rotate, or when the head shows cracks. Running a worn pin transfers wear into the tooth bore and adapter, which is a far more expensive repair.
| Part Number | 1U3252 |
| Product Type | Pin and Retainer |
| Material | 42CrMo Alloy Steel |
| Hardness | HRC 50-54 |
| Pin Diameter | 25 mm |
| Pin Length | 140 mm |
| Net Weight | 0.42 kg |
| Machine Class | 12 Ton Excavator |
| Surface Finish | Black Oxide |
| Application | trenching and utility digging in compacted clay |
| Warranty | 6 months against casting and heat treatment defects |
| Minimum Order | 10 pieces |
| Packing | Neutral carton, no third party brand or logo printed |
| Compatible Reference No. | Notes |
| 1U3252 | Primary number |
| 114-0358 | Interchange reference, verify against sample before ordering |
| 9W2669 | Interchange reference, verify against sample before ordering |
| 1U3302 series | Interchange reference, verify against sample before ordering |
Each pin is oiled, wrapped and part number labelled, then packed in export grade corrugated cartons on a fumigation free pallet. Packing is neutral: no third party brand name, logo or artwork is printed on the product, the label or the carton. We ship FOB Ningbo or Guangzhou, and can quote CIF or DDP depending on destination.
How do I confirm the pin fits my machine?
Send the machine model, bucket part number or a photo of the old pin with its length and diameter. We will cross check the 1U3252 against our fitment data before you order.
Is the pin supplied with the retainer?
Yes, 1U3252 is supplied as a pin and retainer kit. If you only need the pin or only the retainer, state this in the inquiry and we will quote separately.
What is the packing like?
Neutral carton with no third party logo. Each pin is wrapped and part number labelled, and the carton is export grade corrugated suitable for sea freight.
Send your machine model, the number you are replacing and the quantity per size. You will receive a quotation with FOB price, carton count, total weight and lead time within 24 hours on working days. Sample pins for stock sizes can be arranged before the bulk order.